Humminbird Wide View Manuale Utente

mounting bracket. Drill this hole and install the screw after final testing and adjustments have been completed.

INSTALLATION TRANSOM INSTALLATION Step Six - Route the Cable There are several ways to route the transducer cable to the to the area where the contr

INSTALLATION INSIDE THE HULL INSTALLATION INSIDE THE HULL INSTALLATION Inside the hull installation requires the mount system and control head be in

The transducer cannot transmit through air. The water purges any air from between the transducer and the hull and fills any voids in the coarse fiber

INSTALLATION INSIDE THE HULL INSTALLATION 3. Power up the Control Head. 4. Run the boat at various speeds and water depths while observing the scr

INSTALLATION CONTROL HEAD INSTALLATION CONTROL HEAD INSTALLATION Step One - Determine Where to Mount Begin the installation by determining where to

fuse in the connection. If you must wire the control head directly to a battery, be sure to install an inline fuse holder

INSTALLATION CONTROL HEAD INSTALLATION and one amp fuse (not included) for the protection of the unit (Figure 21). Humminbird is not responsible for

Optional: If the cables pass outside the mounting bracket, install the hole cover over the hole and fasten in place using the two #8 x 7/8” (22mm) woo

INSTALLATION CONTROL HEAD INSTALLATION Step Five - Assembling the Connector Holder 1. Insert the cable connectors into the connector holder. The ca

INSTALLATION PREPARATION PARTS SUPPLIED PARTS SUPPLIED Before installing your new Humminbird fishfinder, please ensure the following parts are inclu

INSTALLATION TEST THE INSTALLATION TEST THE INSTALLATION Testing should be performed with the boat in the water, however you can initially confirm b

TESTING THE INSTALLATION After installing your Wide View unit and transducer, you are ready to test the installation. Testing should be performed o

USING THE WIDE VIEW The Wide View is simple to use. Simply press the POWER button, and the unit will automatically locate the bottom, adjust the de

The Wide View allows you a number of ways to display sonar information. Some features are used in conjunction with special accessories such as the

If you are using the Wide Side accessory transducer, the screen layout will look like Figure C. Later, you will learn of another fea

The transmitted sonar signal travels downward, and is reflected back toward the surface by the bottom or other objects for display on

narrow beam, it is located directly under your boat, and is displayed as a solid fish symbol. If a target is seen in the wide beam only, it can be ass

Transducer The Wide View uses a special "dual element" transducer that transmits a wide and narrow beam simultaneously. Using two differe

If you are using the optional Wide Side transducer, and have selected side-looking operation, the adjustments available in the Transducer menu wil

Sensitivity As the Wide View receives returned signals, the sensitivity of the receiver is adjusted automatically based on a number of factors s

INSTALLATION PREPARATION INSTALLATION OVERVIEW Determining How to Mount the Transducer Your Humminbird fishfinder includes a standard transducer. Th

Another use of the Sensitivity menu is to select the bottom representation. The Wide View normally displays a variable Structure ID bottom, which

Range The Wide View adjusts the depth range automatically, so the bottom return is displayed at the bottom 1/3 of the display. This leaves the top

Once you are in zoom, refer to the preview area and adjust the depth of the zoom range by using the UP and DOWN arrow buttons. The Zoom menu will no

Bottom Alarm The Wide View contains an audible alarm to warn you of shallow water depths. This alarm is adjustable from 2' to 99' of dept

ID ID is the automatic identification of target returns based on the strength of the returned signal and other factors. Three options are available

ID "Off" disables the units interpretation of targets, and displays the "raw" sonar information as it is received. Advanced us

Note: The optional Speed & Temperature accessory must be connected for Triplog to work. System Options The System Options menu allows the

Sonar Mode is used to select the Side-Looking mode of operation if the Wide Side transducer is used. This setting changes the mode of operation of

ADVANCED FEATURES The Wide View contains the unique ability to be adaptable in operation to match the experience level of the user. Users inexperie

Also, several kits are available that include a Wide Side transducer with a switch or an additional mounting system. (See Section One, Available Acc

INSTALLATION PREPARATION ALTERNATE MOUNTING METHODS ALTERNATE TRANSDUCERS AND MOUNTING METHODS Your Humminbird fishfinder comes with everything nece

When you exit the "System Options" menu, the view you will see on-screen is shown (bottom, left). Viewing both left and right sides si

Most other menu functions work the same in Wide Side mode as with the standard dual beam transducer. "Bottom Alarm", "Fish Alarm"

INSTALLATION PREPARATION TRANSDUCER EXCHANGE TRANSDUCER EXCHANGE Other transducers are available as replacements for the standard transducer. You ma

INSTALLATION TRANSOM INSTALLATION Do not begin this transducer installation until you read the Installation Preparation in the Operation Guide. This

INSTALLATION TRANSOM INSTALLATION • If the propeller(s) is (are) forward of the transom, it may be impossible to find an area clear from turbulence,

INSTALLATION TRANSOM INSTALLATION Step Four - Mount the Transducer to the Transom 1. Apply silicone sealant to the mounting holes drilled into the