Humminbird Wide 3D Vista Manuale Utente

INSTALLATION TRANSOM INSTALLATION Step Six - Route the Cable There are several ways to route the transducer cable to the to the area where the contr

INSTALLATION INSIDE THE HULL INSTALLATION INSIDE THE HULL INSTALLATION Inside the hull installation requires the mount system and control head be in

The transducer cannot transmit through air. The water purges any air from between the transducer and the hull and fills any voids in the coarse fiber

INSTALLATION INSIDE THE HULL INSTALLATION 3. Power up the Control Head. 4. Run the boat at various speeds and water depths while observing the scr

INSTALLATION CONTROL HEAD INSTALLATION CONTROL HEAD INSTALLATION Step One - Determine Where to Mount Begin the installation by determining where to

fuse in the connection. If you must wire the control head directly to a battery, be sure to install an inline fuse holder

INSTALLATION CONTROL HEAD INSTALLATION and one amp fuse (not included) for the protection of the unit (Figure 21). Humminbird is not responsible for

Optional: If the cables pass outside the mounting bracket, install the hole cover over the hole and fasten in place using the two #8 x 7/8” (22mm) woo

INSTALLATION CONTROL HEAD INSTALLATION Step Five - Assembling the Connector Holder 1. Insert the cable connectors into the connector holder. The ca

INSTALLATION TEST THE INSTALLATION TEST THE INSTALLATION Testing should be performed with the boat in the water, however you can initially confirm b

INSTALLATION PREPARATION PARTS SUPPLIED PARTS SUPPLIED Before installing your new Humminbird fishfinder, please ensure the following parts are inclu

WHAT YOU SEE ON SCREEN The first thing you may notice about the Wide 3D Vista unit is the high-resolution, wide screen LCD display. The LCD display

A valuable accessory available for use with all Wide 3D products is Wide Side. Your unit has the capability of displaying information from a special

The digital depth shown on-screen is the depth of the water directly beneath your boat. As new information is received, the most recent informatio

USING THE 2D VIEW When operating in 2D view, the Wide 3D Vista operates as most normal depth sounders with several exceptions. The six beam 53 de

The signal does not stop there- it is reflected downward again by the surface of the water, and a weak “second return” is usually visible if the d

MENU brings a menu on-screen for adjustment, or if a menu is already present, the next menu in sequence will appear. Menus will go off-screen and no

A setting of –2 sets the sensitivity two steps below what the unit would normally select, so only the largest targets of other returns are displaye

ZOOM Another form of range control is Zoom. Zoom allows selection of various ranges for full screen viewing., while maintaining a view of the fu

To enable Zoom, adjust the horizontal lines to the depth of the zoom range using the UP and DOWN arrow buttons, then enable Zoom using the ENTER b

BOTTOM ALARM The Wide 3D Vista contains an audible alarm to warn you of shallow water depths. This alarm is adjustable from 2' to 99' of

INSTALLATION PREPARATION INSTALLATION OVERVIEW Determining How to Mount the Transducer Your Humminbird fishfinder includes a standard transducer. Th

The Fish Alarm alerts you to the presence of fish, or other targets not attached to the bottom, in the water beneath your boat. The Fish Alarm has 3 d

"ID+", the default setting, provides more information about the location of the target by attaching depth "strings" showing the

TRIPLOG TripLog provides a time/distance calculation, based on input from the speed accessory. The timer is started when the unit is first powered, a

Scroll Rate controls the rate of update of the display. There are five rate settings available. The default setting is rate 4 - you may speed up or

particular viewpoint, or just for personal preference. This setting is remembered even after the unit is turned off. Units-Speed allows a selection b

"Diagnostic" is selected with the sonar mode option of the System menu. It is a special screen that displays the raw sonar information bei

The Wide Side transducer is available as a trolling motor mount, a transom mount, or a portable mount. Wide Side can be connected directly to your Wi

Your Wide 3D Vista is now configured for Wide Side operation. When you exit the "System Options" menu, the view you will see on-screen i

The information collected is controlled by pressing the VIEW button. Pressing VIEW toggles the options "both", "right', "left

INSTALLATION PREPARATION ALTERNATE MOUNTING METHODS ALTERNATE TRANSDUCERS AND MOUNTING METHODS Your Humminbird fishfinder comes with everything nece

INSTALLATION PREPARATION TRANSDUCER EXCHANGE TRANSDUCER EXCHANGE Other transducers are available as replacements for the standard transducer. You ma

INSTALLATION TRANSOM INSTALLATION Do not begin this transducer installation until you read the Installation Preparation in the Operation Guide. This

INSTALLATION TRANSOM INSTALLATION • If the propeller(s) is (are) forward of the transom, it may be impossible to find an area clear from turbulence,

INSTALLATION TRANSOM INSTALLATION Step Four - Mount the Transducer to the Transom 1. Apply silicone sealant to the mounting holes drilled into the

mounting bracket. Drill this hole and install the screw after final testing and adjustments have been completed.